(0 item) - $0.00

You have no items in your shopping cart.


Currie Rockjock III High Pinion Dana 60 Front JK - 1 TON ASSEMBLY Zoom

Currie Rockjock III High Pinion Dana 60 Front JK - 1 TON ASSEMBLY

JEEP JK RockJock 60 1 Ton Frontend Unit (5 Lug, 1/2" Studs, Bolt-In)

Availability: In stock

$5,550.00 $4,699.00

* Required Fields

$5,550.00 $4,699.00
Product Description


    Highest measured ground clearance of any 60 class axle on the market (including the integrated skid plate), guess the other guys have trouble reading a tape measure...

    The RockJock III high pinion frontend assembly for the 2007 and up Jeep JK includes the complete housing featuring the 65-45-12 ductile iron housing center (highest ground clearance 60 on the market), AR400 heat treated bottom skid plate allowing the axle to slide over rocks easily, 3" x .375" wall d.o.m. steel tubes, 1 ton inner knuckles, 5/16" thick heavy steel diff cover, yoke, and all new heavy duty Currie Jeep JK suspension brackets mounted. Upper control arm brackets are equipped with Johnny Joint rod ends for maximum articulation.

    The RockJock 60 crate axle is a complete front axle assembly, reusing only the stock JK calipers from the vehicle.

    Center Section RockJock 60 stage-1 nodular iron high-pinion radius bottom center section with thicker walls and webbing
    Pinion Bearing Large diameter front pinion bearing matched to rear bearing
    Pinion Oiling High volume flow-thru recirculating oil system
    Gear Set Standard reverse cut Dana 60™ (compatible with super 60 reverse cut gears)
    Pinion Yoke 1350 u-joint
    Skid Plate AR400 hardened steel
    Differential Cover RockJock nodular-iron cover with integrated Johnny Joint control arm mount, Red
    Axle Tubes 3 inch diameter, .375 wall DOM tube
    Axles Currie Perfromance 35-spline (1.5" diameter) 4340 chromoly inner and outer axle shafts with 1480 u-joints
    Knuckles RockJock heavy duty forged 1-ton inner and outer knuckles with "high steer" steering arm
    Unit Bearings 1 ton unit bearings with 5 on 5 ½” bolt pattern, ½” wheel studs, JK tone rings installed for ABS and ESP retention
    Hubs Warn Premium 35-spline locking hubs
    Brake Rotor 13.250" vented rotors (over 1" larger diameter than stock JK, provides increased brake force), with zinc plated caliper brackets
    Brake Calipers Calipers not included, designed to reuse the stock JK front calipers
    Tie Rod Currectlync® 1 3/8” diameter, .250 wall heat treated chromoly tube with 7/8” 1-ton tie rod ends
    Suspension Brackets Heavy gauge 3/16” steel mounting brackets with multiple mounting locations that enable the suspension geometry to be tuned
    Control Arm Mounts Johnny Joints installed with ½” greasable bolt
    Geometry Optimized for 4” lift kits with 5 degrees of pinion angle to reduce driveshaft angle and 5 degrees of caster for improved steering
    Width 68.750” wide (between wheel mounting surfaces), enables increased turning angle with large tires
    Wheel Bolt Pattern 5 on 5 ½ with ½” wheel studs

    Special shipping and handling required for this item, select shipping or local pickup. The added freight fee is in addition to the shipping fee added at check out.

    These are a build to order direct from Currie and typically take between 10-20 business days to complete and ship.

Additional Information

    Additional Information

    freeship No
    Manufacturer Currie Enterprises
    Short Description JEEP JK RockJock 60 1 Ton Frontend Unit (5 Lug, 1/2" Studs, Bolt-In)
CMS tab