(714) 875-2414 RWK HAUS SUPPLY DISCOUNT - GEARS, LOCKERS, POSI'S, AXLES, ALL YOUR DRIVETRIAN NEEDS
(0 item) - $0.00

You have no items in your shopping cart.

section

Jeep JK RockJock 60 Rearend Unit (35 Spline, 5 Lug (dual) w/ 1/2" studs, Bolt-In) Zoom

Jeep JK RockJock 60 Rearend Unit (35 Spline, 5 Lug (dual) w/ 1/2" studs, Bolt-In)

Be the first to review this product

SKU: JK-RJIIIRS1
Jeep JK Rear Currie Rockjock III housing assembly.

Availability: In stock

$2,550.00 $2,150.00

* Required Fields

$2,550.00 $2,150.00
Product Description

    Details

    The RockJock 60 high pinion crate axle is a complete rear axle assembly, reusing only the stock JK rotors, calipers and ABS wheel sensors from the vehicle

     

    Built to the legendary Currie Standard with exclusive features including:

    • RockJock high-pinion, radius bottom center section greatly improves obstacle slide-over by presenting a smooth curve rather than the sharp edge found on other 60 housings
    • Highest measured ground clearance of any 60 on the market (and that’s including the integrated skid plate), guess the other guys can’t read a tape measure
    • Integrated AR400 hardened steel skid plate resists deformation and gouging to slide over obstacles far better than iron housings or mild steel plates
    • Large diameter pinion bearings to handle the increased load of reverse geometry gears
    • High volume flow-thru recirculating oil system keeps pinion bearings bathed in cool oil, reducing operating temperatures and eliminating oil starvation issues
    • Large 3-inch diameter .375 thick axle tubes deliver superior strength without sacrificing ground clearance or being overweight
    • Currie Performance 35-spline 4340 chrome moly semi-floating axles, the largest and strongest standard axle in the industry
    • Massive Set80 axle bearings allow for larger axle diameter through the bearing for increased strength
    Center Section RockJock 60 stage-1 nodular Iron high-pinion radius bottom center section with thicker walls and webbing
    Pinion Bearing Large diameter front pinion bearing matched to rear bearing
    Pinion Oiling High volume flow-thru recirculating oil system
    Gear Set Standard Dana 60™, compatible with super 60 reverse cut gears
    Pinion Yoke 1350 u-joint
    Skid Plate AR400 hardened steel
    Differential Cover RockJock nodular-iron cover with gasketed fill plug with dipstick, Red
    Axle Tubes 3 inch diameter, .375 wall DOM tube
    Axle Bearings Set 80 tapered roller bearing
    Axles Currie Performance semi-floating, 35-spline 4340 chromoly axles with JK tone rings installed for ABS and ESP retention
    Brake Rotor Not included, reuses the stock JK rear rotors
    Brake Calipers Not included, reuses the stock JK rear calipers
    Suspension Brackets Heavy gauge 3/16” steel mounting brackets with multiple mounting locations that enable the suspension geometry to be tuned
    Geometry Optimized for 4” lift kits with 5 degrees of pinion angle to reduce driveshaft angle and 5 degrees of caster for improved steering
    Width 66” wide (between wheel mounting surfaces)
    Wheel Bolt Pattern Dual pattern, 5 on 5” with ½” studs (installed) and 5 on 5 ½” (holes)

    Special shipping and handling required for this item, select shipping or local pickup. These are a build to order direct from Currie and typically take between 10-20 business days to complete and ship.

    This unit requires the use of 17" wheels. 2012 and newer vehicles will need a computer programmer, such as the AEV ProCal Module to reset the gear ratio and tire height in the vehicle's computer.

Additional Information

    Additional Information

    SKU JK-RJIIIRS1
    freeship No
    Manufacturer Currie Enterprises
    Short Description Jeep JK Rear Currie Rockjock III housing assembly.
CMS tab

You may also be interested in the following product(s)

  • Currie Rockjock III High Pinion Dana 60 Front JK - 1 TON ASSEMBLY

    Currie Rockjock III High Pinion Dana 60 Front JK - 1 TON ASSEMBLY

    $5,550.00 $4,699.00